{"id":3524,"date":"2026-10-21T14:27:18","date_gmt":"2026-10-21T06:27:18","guid":{"rendered":"http:\/\/www.ykgai.com\/blog\/?p=3524"},"modified":"2026-10-21T14:27:18","modified_gmt":"2026-10-21T06:27:18","slug":"what-is-the-mounting-method-of-the-80g-radar-level-meter-48dc-6ef26e","status":"publish","type":"post","link":"http:\/\/www.ykgai.com\/blog\/2026\/10\/21\/what-is-the-mounting-method-of-the-80g-radar-level-meter-48dc-6ef26e\/","title":{"rendered":"What is the mounting method of the 80G Radar Level Meter?"},"content":{"rendered":"

When I first started shipping 80G radar level meters to industrial clients back in 2019, I noticed a pattern: half the field issues I got calls about weren\u2019t from faulty hardware\u2014they were from bad installation. A client in the chemical processing sector once told me their meter kept giving inconsistent readings, until I asked to check how it was mounted. Turns out they\u2019d installed it 10 inches above the liquid\u2019s maximum level, with the antenna pointed straight at the tank wall. That mistake cost them three days of production downtime and hundreds in lost raw materials. Today, as someone who\u2019s spent four years walking through refineries, food processing plants, and water treatment facilities to set up these meters, I can tell you the mounting method of an 80G radar level meter isn\u2019t just a technical detail\u2014it\u2019s what makes the meter reliable, accurate, and worth the investment you\u2019re making. 80G Radar Level Meter<\/a><\/p>\n

<\/p>\n

First, let\u2019s get clear on why 80G radar is different from older radar types, because that difference shapes how you mount it. Unlike 26G radar, which uses a longer wavelength that can be distorted by steam, foam, or heavy vapor, 80G radar operates at a much higher frequency\u2014around 80 GHz\u2014with a narrower beamwidth. That narrower beam is why it can cut through messy industrial environments, but it also means you can\u2019t just stick it anywhere. If you mount it wrong, that tight beam might bounce off tank walls, piping, or even the top of the tank\u2019s access hatch instead of reflecting off the liquid surface. I remember another client in the beverage industry who mounted their 80G meter too close to a tank\u2019s agitator; the beam bounced off the agitator blades and gave a reading that was 2 feet off the actual level for a month before they caught it.<\/p>\n

Let\u2019s break down the step-by-step mounting method we recommend to every client, tailored to 80G specifically, not generic radar rules. First, the location choice: you never want to mount an 80G radar level meter directly above an agitator, nozzle, or any other protruding object. Those objects act as interference points for the narrow beam. The sweet spot is at least 300 mm (about 12 inches) away from any tank internal obstructions\u2014agitator shafts, temperature sensors, inlet\/outlet pipes, even the reinforcement ribs on a tank wall. For vertical cylindrical tanks, the ideal spot is dead center. That\u2019s not a random rule; it\u2019s because a beam aligned with the center has the most unobstructed path to the liquid surface, so the reflection is sharp and consistent. If you have to mount off-center, we advise a minimum 15-degree offset from the tank wall. This prevents the beam from hitting the wall and creating a false echo that the meter might misinterpret as a level reading.<\/p>\n

Next, the mounting height. A common mistake is mounting the meter too low, just above the maximum liquid level. If you do that, when the liquid fills the tank and reaches that mounting point, the beam will start reflecting off the liquid surface right below the antenna, which causes the meter to lose signal. We always tell clients to mount the meter at least 500 mm (20 inches) above the highest possible liquid level, and no more than 1 meter (39 inches) above that maximum. Wait, why that upper limit? Because the 80G\u2019s narrow beam has a effective range, and mounting it too high can make the beam spread out too much, reducing the signal strength. For tanks over 10 meters tall, that upper limit becomes even more important\u2014some clients think mounting higher gives a clearer line of sight, but it often does the opposite for 80G, because the beam\u2019s energy dissipates over distance. I\u2019ve seen a 20-meter tall tank where the meter was mounted 2 meters above the max level; the signal was so weak it only worked 60% of the time, until we lowered it to 800 mm above max level, and readings stabilized within an hour.<\/p>\n

Then, the antenna type choice tied to mounting. 80G radars come with two common antenna types: lens antennas and horn antennas, and each has its own mounting requirements. Lens antennas are smaller, with a wider beam, which makes them good for tanks with more steam or foam, but they need to be mounted in a way that keeps the lens clear of condensation. Horn antennas have a narrower beam, better for low-interference tanks, but they need more clearance around them. We always match the antenna to the tank\u2019s conditions, and adjust mounting accordingly. For example, a client in a power plant with a coal ash storage tank (which has heavy dust and vapor) would get a lens antenna, and we\u2019d mount it with a protective windscreen that\u2019s mounted flush to the tank top, so the lens is shielded but the beam still passes through. For a food processing client with a clean, open tank for syrup, a horn antenna works, and we mount it with a slightly raised flange to prevent any syrup drips from running down the antenna body.<\/p>\n

Another critical part of the mounting method is the sealing and flange connection. You can have the perfect location and height, but if the flange isn\u2019t sealed right, condensation or vapor can get inside the antenna housing, ruining the meter\u2019s electronics. 80G radars use standard process flanges\u2014usually DN50 or DN80 for industrial use\u2014but when mounting, you have to make sure the flange is aligned perfectly with the tank\u2019s top opening. If the flange is tilted even a few degrees, the beam will be off-center, leading to those false echoes I mentioned earlier. I once had a client who used an old, warped flange adapter because they thought \u201cit\u2019ll work fine,\u201d and the meter kept giving fluctuating readings until we replaced the adapter with a flat, new flange and aligned it with the tank\u2019s center. That small adjustment cut their reading error by 98%. We also recommend using a PTFE or EPDM gasket for sealing, not a generic rubber one, because those materials resist the high temperatures and chemicals common in industrial tanks, and they don\u2019t degrade as fast over time.<\/p>\n

Wait, what about when tanks have dome-shaped tops? That\u2019s a scenario I run into a lot, especially in refineries. A flat top is easy to mount on, but a dome top curves upward. The key here is to mount the meter at the highest point of the dome, but not so high that the beam has to travel down into the tank. If you mount too high on a dome, the beam will reflect off the curved surface of the dome instead of going straight to the liquid. We usually calculate the mount point so that the distance from the antenna to the liquid\u2019s max level is still within that 500 mm to 1 meter range, even on a dome. For very large domes (over 10 meters in diameter), we advise using a guide wave radar as a backup, but 80G can work if the mount point is correct.<\/p>\n

Also, cable routing and terminal connections are part of the mounting method that people often overlook. I\u2019ve had clients mount the meter perfectly, but then run the signal cable too close to power cables, which causes electromagnetic interference (EMI) that distorts the radar signal. When we mount the meter, we tell clients to run the signal cable at least 300 mm away from any power lines, motor leads, or other electrical equipment. We also use shielded cables, and ground the shield correctly at both ends\u2014one end at the meter, one end at the control panel\u2014to prevent EMI. A client in a water treatment plant had their meter mounted on a clarifier, right next to a 480V power line, and the readings were jumping up and down; when we rerouted the cable and grounded it properly, the readings stayed consistent within 1 cm of actual level. That\u2019s a small part of the mounting process, but it\u2019s just as important as where you place the antenna.<\/p>\n

Let\u2019s address a common myth: some clients think 80G radar can be mounted through a sidewall of a tank, instead of the top. That\u2019s a bad idea for most cases. Mounting through a sidewall means the beam has to pass through the tank wall, which is usually made of steel, and that distorts the signal. Even if you use a non-metallic tank, the sidewall thickness can cause reflection issues. The only time we recommend sidewall mounting is for very small tanks (under 5 meters tall) where top mounting isn\u2019t possible, and even then, we use a special window adapter that\u2019s made of a material transparent to 80G radar waves. But for 90% of industrial applications, top mounting is the way to go, and following the guidelines we lay out for that gives the best results.<\/p>\n

Now, why does this matter to you as a buyer? When you invest in an 80G radar level meter, you\u2019re not just paying for the device\u2014you\u2019re paying for consistent, accurate level readings that keep your production running, prevent overfilling, and avoid safety hazards. A poorly mounted meter can cost you more in downtime than the meter itself is worth. That\u2019s why we don\u2019t just sell meters; we walk through these mounting steps with every client, either in person (if they\u2019re local) or over a video call to guide them through the process, and we offer mounting kits that come with all the gaskets, flanges, and tools needed to get it right.<\/p>\n

<\/p>\n

If you\u2019re currently having issues with your 80G radar level meter\u2019s accuracy, or you\u2019re planning to install a new system and want to make sure it\u2019s mounted correctly, don\u2019t leave it to chance. Connect with our team to discuss your specific tank conditions, layout, and needs. We\u2019ll walk you through every part of the mounting method, from choosing the right location to sealing and cable routing, to make sure your meter performs as it should. Whether you\u2019re in food and beverage, chemical processing, water treatment, or power generation, we have the expertise to help you get the most out of your 80G radar level meter.<\/p>\n

80G Radar Level Meter<\/a> References:<\/p>\n

    \n
  1. International Electrotechnical Commission (IEC) 61508: Functional safety of electrical\/electronic\/programmable electronic safety-related systems, 2010<\/li>\n
  2. Emerson Process Management, \u201cGuidelines for Radar Level Transmitter Installation and Mounting,\u201d 2021<\/li>\n
  3. Endress+Hauser, \u201c80 GHz Radar Level Measurement: Application Guidelines for Industrial Tanks,\u201d 2022<\/li>\n
  4. American Water Works Association (AWWA), \u201cLevel Measurement Practices for Water and Wastewater Facilities,\u201d 2019<\/li>\n<\/ol>\n
    \n

    Shandong Aipuxin Automation Instrument Co., Ltd.<\/a>
    Shandong Aipuxin Automation Instrument Co., Ltd. is one of the most professional 80g radar level meter manufacturers and suppliers in China, specialized in providing high quality customized service. We warmly welcome you to wholesale cheap 80g radar level meter in stock here from our factory. For price consultation, contact us.
    Address: Huigu Phase 1, Zhongnan High-tech Canal New City, Rencheng District, Jining City, Shandong Province
    E-mail: aipuxin0124@gmail.com
    WebSite:     https:\/\/www.aipxin.com\/<\/a><\/p>\n","protected":false},"excerpt":{"rendered":"

    When I first started shipping 80G radar level meters to industrial clients back in 2019, I … What is the mounting method of the 80G Radar Level Meter?<\/span>Read more<\/a><\/p>\n","protected":false},"author":318,"featured_media":3524,"comment_status":"closed","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[1],"tags":[3487],"class_list":["post-3524","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-industry","tag-80g-radar-level-meter-4f85-6f26fa"],"_links":{"self":[{"href":"http:\/\/www.ykgai.com\/blog\/wp-json\/wp\/v2\/posts\/3524","targetHints":{"allow":["GET"]}}],"collection":[{"href":"http:\/\/www.ykgai.com\/blog\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"http:\/\/www.ykgai.com\/blog\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"http:\/\/www.ykgai.com\/blog\/wp-json\/wp\/v2\/users\/318"}],"replies":[{"embeddable":true,"href":"http:\/\/www.ykgai.com\/blog\/wp-json\/wp\/v2\/comments?post=3524"}],"version-history":[{"count":0,"href":"http:\/\/www.ykgai.com\/blog\/wp-json\/wp\/v2\/posts\/3524\/revisions"}],"wp:featuredmedia":[{"embeddable":true,"href":"http:\/\/www.ykgai.com\/blog\/wp-json\/wp\/v2\/posts\/3524"}],"wp:attachment":[{"href":"http:\/\/www.ykgai.com\/blog\/wp-json\/wp\/v2\/media?parent=3524"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"http:\/\/www.ykgai.com\/blog\/wp-json\/wp\/v2\/categories?post=3524"},{"taxonomy":"post_tag","embeddable":true,"href":"http:\/\/www.ykgai.com\/blog\/wp-json\/wp\/v2\/tags?post=3524"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}